• 19” Widescreen LCD Television TLA-01901C Questions? Need some help? This manual should help you understand your new product.

If you have questions, call our toll-free number found on the insert with this icon: Or visit www.polaroid.com.

Hi there, There should be a button on the narrow edge on the right side of the TV labelled INPUT. Press this button once to bring up the input menu on the TV screen, you should then be able to highlight the input from this list using the CHANNEL UP/DOWN buttons on the side of the TV. It may actually be the VOL +/- buttons to move up and down the list - I can't honestly remember so you may need to try a couple of times to get it right. Finally I think you need to press the INPUT button again to select the highlighted input It's best to switch the external input device on before doing this so there is a signal to the TV. It's easier to see when you have selected the correct input this way.

TLA-04011C, TLXB-4011, TLXB-4241 SERVICE MANUAL. Model Specifications are located in User Manual. Go to polaroid.com to obtain User. Polaroid Service Manual.

If you still can't select the correct input, please let me know and I will check on the exact method for switching this TV without the remote. I'm working from memory here! Hope this helps. Regards, BElectric. Answered on Sep 28, 2016. Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center.

If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary. Before going further; try a hard reset first.

If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better.

This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here. Answered on Apr 29, 2016. No picture can be caused by dead T-CON board, main board, 24vdc power supply not supplying power to the backlights inverter board, bad backlights inverter board.

So inspect for bad caps fisrt and also try the instruction below. First, look at the screen in darkened room to see if you can see any slight glow from the screen, if it does, then the problem can be the T-CON (not getting the 12vdc) or the main logic board not feeding the signals to the T-CON board. If not, next place to check will be the power supply module, make sure it has 24vdc which is required by the backlight inverter to work, the reason for not having 24vdc can be from bad DC filter caps (leaking/bulging top, high ESR) or short circuits in the inverter board which will cause the 24vdc supply to go into shutdown mode, so you may have to disconnect the power cable that feed the inverter board to see if the 24vdc will work without the inverter board hookup, you will need to apply about 3~4 amp of load to the 24vdc to make sure it can handle that. Torent Solidworks 2008 Sp0 Real Serial Crack.

There are fuses on the backlight inverter boards also. Roms Gba Gameboy Advance Zelda Minish Cap. So there is some troubleshooting you will have to do to find out the causes of the problem you are having. If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on: Basic LCD monitor and TV troubleshooting guide: Failed TV and Monitors pictures: Learn about bad caps: Parts: Capacitors kit: he can make you a set of caps. Or, just make sure to use caps with low ESR, 105c, high ripple current and long life rating such as PANASONIC FM or FC series. Please post back what you find. Answered on May 18, 2014. If you wish to buy its original remote control, contact the authorized service center, or authorized dealer to your device brand.

To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability?